Technical Data

Extruded alloys

Eastern Aluminum Extrusion Factory can extrude the majority of 6XXX alloy series in various tempers but most common alloys & tempers used are:
EN-AW 6060 (Al MgSi0,5) DIN 3.3206
EN-AW 6063 (Al Mg0,7Si) DIN 3.2315
EN-AW 6005 (Al MgSi0,7)

Extruded alloys

Eastern Aluminum Extrusion Factory can extrude the majority of 6XXX alloy series in various tempers but most common alloys & tempers used are:
EN-AW 6060 (Al MgSi0,5) DIN 3.3206
EN-AW 6063 (Al Mg0,7Si) DIN 3.2315
EN-AW 6005 (Al MgSi0,7) DIN 3.3210
EN-AW 6082 (Al Si1MgMn) DIN 3.2315

Chemical Composition

According to EN 573-3 (EN- AW chemical composition %)
Alloy Si Fe Cu Mn Mg Cr Zn Ti Other Al

                 

Other

 

Alloy

Si

Fe

Cu

Mn

Mg

Cr

Zn

Ti

Each

Total

Al

6060

0.30-0.60

0.10-0.30

0.10

0.10

0.35-0.60

0.05

0.15

0.10

0.05

0.15

Rest

6063

0.20-0.60

0.35

0.10

0.10

0.45-0.90

0.10

0.10

0.10

0.05

0.15

Rest

6005

0.50-0.90

0.35

0.30

0.50

0.40-0.70

0.30

0.20

0.10

0.05

0.15

Rest

6082

0.70-1.30

0.50

0.10

0.40-1.00

0.60-1.20

0.25

0.20

0.10

0.05

0.15

Rest

Alloy Si Fe Cu Mn Mg Cr Zn Ti Other Al

Tempers

According to EN 515


Alloys and Tempers

6060

6063

6005

6082

O

O

O

O

T4

T4

T4

T4

T6

T6

T6

T6

O             Annealed wrought alloys
T4           Solution heat treated and naturally aged.
T5           Cooled from an elevated temperature and artificially aged (precipitation hardened)

T6           Solution heat treated and artificially aged (precipitation hardened). Press quenching required.

Mechanical Properties

According to EN 755-2

 

* For different wall thicknesses of a given profile, the lowest specified values of properties shall be
considered as valid for the whole profile cross section.
** The values for the HB hardness are indicative only.

 

Tolerances

The quality control department at Eastern Aluminum Extrusion Factory abides with the following standards for the production quality control and delivery of aluminum profiles.

Aluminium and aluminum alloys- Extruded rod/bar, tubes and profiles
EN 755-1 Technical conditions for inspection & delivery
EN 755-2 Mechanical properties
EN 755-3 Round bars, tolerances on dimension & form
EN 755-4 Square bars, tolerances on dimension & form
EN 755-5 Rectangular bars, tolerances on dimension and form
EN 755-6 Hexagonal bars, tolerances on dimension and form
EN 755-7 Seamless tubes, tolerances on dimension and form
EN 755-9 Profiles, tolerances on dimension and form

Extruded precision profiles for Architecture in alloys EN- AW 6060 & EN- AW 6063

EN- 12020-1 Technical conditions for inspection and delivery (precision profiles)
EN- 12020-2 Tolerances on dimension and form (precision profiles)

Limits

Maximum Profile weight: 10.0 kg/m
Minimum Profile weight: 0.07 kg/m
Maximum Profile length (Aged): 16.0 m
Maximum Profile length (Coated): 7.0 m
Minimum Thickness: 0.7 mm
Special sizes under request